|
The GP100 is a family/line of six-shot double action .357 Magnum/.327 Federal Magnum revolvers made by Sturm, Ruger & Co., manufactured in the United States. It was introduced in 1985 as a second generation of the Ruger double-action, exposed-hammer revolvers intended to replace Ruger's Security- / Service- / Speed-Six line. It was made stronger with the intent to fire an unlimited number of full-power .357 Magnum rounds and has been produced in a number of variations with three basic barrel lengths (3 in / 76 mm, 4 in / 102 mm, and 6 in / 152 mm), various barrel profiles (full lug and half lug), fixed or adjustable sights, and in blued carbon steel or polished stainless steel. ==Description and features== The GP100 was an evolution of an earlier Ruger double-action revolver, the Security Six. The first significant change was introduced with the Ruger Redhawk and that involved a new locking mechanism with a lever on the crane rather than using the end of the ejector rod to lock. Another change was the shape of the frame. Traditional revolver frames had exposed metal at the front and rear of the grips, with the frame determining the shape of the grips. This meant that to have a round butt concealed carry version and a square butt holster or target version of the same gun usually meant having two different frame shapes. The GP100 series, instead, used a small rectangular "peg" grip large enough to enclose the hammer spring and strut. The grips could then be any shape desired, as long as they were large enough to enclose the peg. This was not a new innovation having been used by Dan Wesson and, to some degree, by High Standard revolvers that predated the GP100. The Dan Wesson patent () was granted in 1972 and Ruger's patent () was granted in 1986. The stock grips are made of Santoprene, a soft, chemical resistant elastomer that helped absorb the recoil of firing. Panels on the side, made of black plastic, goncalo alves wood or rosewood, provide contrast to the flat black of the Santoprene. The grips are now Hogue one piece rubber grips standard. ((Ruger Website) ) The GP100 shared the crane lock from the Redhawk that was later used in the small frame SP101 revolver. All of these models use the same thickness on the solid frame and double latching system as used on the heavy .44 Magnum. Because of these features, the GP100 series is widely described as one of the strongest medium frame revolvers ever made.〔 The GP100 is manufactured in .357 Magnum, .38 Special and .327 Federal Magnum calibers. Available Barrel lengths are 3" (76mm), 4.2" (107mm) and 6" (152mm) with partial or full length underlugs.〔(Ruger GP100 Double-Action Revolver Models ) at Ruger.com〕 Blued Steel, or Stainless Steel finishes are available with stainless model numbers preceded by a "K". The Firing pin of the GP100 is mounted inside the frame. The Transfer bar of the GP100 is connected directly to the trigger. The transfer bar must be present between the hammer and the firing pin in order for the cartridge to be fired. The transfer bar only assumes the required position when the trigger is pulled completely rearward. GP100 models are available with fixed or adjustable sights. Fixed sight models are designated by a "F" suffix model number. When the cylinder is closed and the gun is at the point of firing, the cylinder crane is locked into the frame at the front and rear of the crane and by the cylinder lock at the bottom of the crane opening. The GP100 disassembles into three major modules with only limited use of tools. This allows the user to easily clean the revolver after shooting. The design of the gun eliminates the need for a frame "sideplate", a feature which contributes to the GP100's reputation for strength.〔 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「Ruger GP100」の詳細全文を読む スポンサード リンク
|